Digital Electronic Overspeed Warning Windshield Projector M3 OBD2 HUD Auto Accessories Car Head
NOT COMPATIBLE:All French and Italian car models cannot be used.Oil-electric hybrid and diesel car, pickup truck, RV, car computer modified car.American Cars: models produced before 2004 and 2004.Some of South Korea's Kia and Hyundai models (Hyundai Sonata 2013, Kia Soul PS 2017). Japan Cars: Suzuki, Mazda6, Infiniti (QX50,Q50,Q501), Toyota avanza 2013, Lexus (is250,ex250,), Honda Jazz, and cars that produced before 2008.Restore setting（Two ways）:Method one：Unplug the power supply,long press 'M' button and hold until all of the LED lights on while Plug the power again.Method two：Long press 'M' button to enter into setting mode and adjust the value of 0 to 1 in Menu 12. Long press again to save and exit.Fault code clearance:long press '+' button and hold until all of the LED lights on, long press again to exitTurn off/on the buzzerLong press and hold the ‘-’ button to turn off the buzzer, again to turn on.The car are with Automatic start/stop system or Gas-electric hybrid vehicleLong press "M” button to enter into setting mode and adjust the value of Turn-off Voltage to 1 in Menu 10. Long press again to save and exit.Menu settingPlease watch the reflective image on the windshield for operation when setting.Long press and hold the 'M' button to enter into setting menus (1-12). The menu is displayed 1,use the '+' button to increase the menu options,short press '+' or '-' button to adjust the parameter value, short press 'M' button to return to the menu, long press 'M' button to save and exit.OBD Troubleshooting:1.The screen without any display, and no powerPlease do these operations: If OBD cable is tight enough,pull the OBD cable out several times. Try another car to test. 2.When HUD power on,HUD only shows the car voltage and be automatic power off after 30 seconds driving.HUD is only available for cars with OBD2 and EOBD agreement(European:manufactured after 2003, Other region: after 2007)HUD Products don’t support JOBD and OBDI,if your car is these agreement(manufactured before 2008),please replace with other cars that comply with OBD2 interface.3.Wrong operation lead to crashes A.If your car equip with other OBD devices (parking sensor, TPMS monitor,car window closer,ELM27)B.If your car had been modified(central control navigation,electronic throttle controller,speed cruise,refresh the computer system,One-click start-up,keyless entry,remote startup)will cause a crash,unplug other OBD devices and do the factory settings (more details please refer to the menu table), unplug the one-point two-wire and use the HUD alone or replace with other cars.4. Inaccurate speedIn the case of power-on,long press the 'M' button in to enter into menu option,menu displays 1,parameter displays 107.Fine tuning of the values according to the difference between HUD and car instrument(Example:the instrument displays 100 KM but HUD displays 105KM,then calculation should be default value 107-5=102.Long press the 'M' button to save your adjustment and exit.5. The cars are with Automatic start/stop system and Hybrid electric vehicle After the car starts and stops automatically, the engine stops running. The HUD shuts down after 20 seconds. The turn off voltage can be adjusted to 1V in Menu 10.6.HUD can not auto power off(RPM or Speed not at 0)When HUD is power on,long press the button in to enter into menu,set the voltage from 0 to 13.2V or 13.5V(Menu 10).HUD will turn off after 3 minutes.7.HUD will automatically restart Indicates that the car voltage is higher than the starting voltage 13.2 volts,what you should do is to set voltage to 13.6-13.8V(Menu).HUD will automatically on when voltage is higher than 13.2v.